Effect of preheating and ultrasound application of resin-based luting agents on the failure load of a lithium disilicate glass-ceramic.

PURPOSE: To assess the effect of preheating resin-based materials and ultrasound application on the failure load of a lithium disilicate glass-ceramic. MATERIALS AND METHODS: Ninety ceramic specimens were produced (14×12×1.0 mm) and divided into 9 groups (n = 10) to be bonded to a dentin analog (Nema G10) with light-cured luting agent (LC), flowable resin composite (FL), and supra-nano filled resin composite (SN), as follows: LC/R - LC at room temperature; LC/P - preheated LC; LC/P/U - preheated LC and Ultrasound; FL/R - FL at room temperature; FL/P - preheated FL; FL/P/U - preheated FL and Ultrasound; SN/R - SN at room temperature; SN/P - preheated SN; SN/P/U - preheated SN and Ultrasound. The failure load test was performed in a universal testing machine with the aid of acoustic detection. The data was analyzed with two-way ANOVA (for failure load) and Weibull statistics (Weibull modulus - m and characteristic strength, based on 95% confidence intervals - CI). RESULTS: The analyses of failure load revealed no statistically significant difference among groups considering the type of luting agent (P = 0.075; F = 2,673), the application method (P = 0.772; F = 2,259), and the interaction between them (P = 0.297; F = 1,248). The characteristic strength did not show differences among groups (95% CI). The m, which indicates structural reliability, showed lower values for SN/P/U and SN/P, with a difference from other selected groups (95% CI). CONCLUSION: Preheating of resin-based materials and ultrasound application did not affect the failure load of lithium disilicate glass-ceramic. Lower reliability was observed with supra-nano filled resin composite.

Fatigue resistance of monolithic and multilayer zirconia crowns using veneer layering or CAD-on technique.

This study aims to evaluate the fatigue resistance of monolithic zirconia (Yz) and multilayer ceramic structures using the CAD-on technique in different thicknesses. Fifty (N=50) standardized single crowns preparations were made in fiberglass-reinforced epoxy resin (NEMA grade G10), digitalized, and restorations were machined in CAD-CAM, composing 5 groups (n= 10): Control: 1.5 mm (milled zirconia framework + manual layered porcelain); Yz monolithic 1.5 mm; Yz monolithic 1.0 mm; CAD-on 1.5 mm; and CAD-on 1.0 mm (milled zirconia framework 0.5 mm thickness bonded by a low fuse ceramic to a milled lithium disilicate layer of 1.0 mm or 0.5 mm, respectively). The G10 bases were conditioned with 10% hydrofluoric acid; the crowns were air abraded with 110 µm alumina particles; and then luted onto each other with self-adhesive resin cement. A cyclic fatigue test was performed (initial load: 400N for 10,000 cycles, frequency of 20 Hz, step size of 200N) until failure, and the data was submitted to a survival statistical analysis. No failures were observed at Yz monolithic 1.5 mm. High and similar performance was observed for Cad-On groups and Yz monolithic 1.0 mm. The control group depicted the worst behavior. The Weibull modulus of CAD-on 1.5 mm was higher than the control while being similar to the other conditions. Both the monolithic systems and the CAD-on technique showed high and similar fatigue fracture behavior and survival rates, which were also higher than the control bilayer system. Both systems reduced the occurrence of delamination failures, making them suitable for clinical use.

Fatigue resistance of monolithic and multilayer zirconia crowns using veneer layering or CAD-on technique

Abstract This study aims to evaluate the fatigue resistance of monolithic zirconia (Yz) and multilayer ceramic structures using the CAD-on technique in different thicknesses. Fifty (N=50) standardized single crowns preparations were made in fiberglass-reinforced epoxy resin (NEMA grade G10), digitalized, and restorations were machined in CAD-CAM, composing 5 groups (n= 10): Control: 1.5 mm (milled zirconia framework + manual layered porcelain); Yz monolithic 1.5 mm; Yz monolithic 1.0 mm; CAD-on 1.5 mm; and CAD-on 1.0 mm (milled zirconia framework 0.5 mm thickness bonded by a low fuse ceramic to a milled lithium disilicate layer of 1.0 mm or 0.5 mm, respectively). The G10 bases were conditioned with 10% hydrofluoric acid; the crowns were air abraded with 110 μm alumina particles; and then luted onto each other with self-adhesive resin cement. A cyclic fatigue test was performed (initial load: 400N for 10,000 cycles, frequency of 20 Hz, step size of 200N) until failure, and the data was submitted to a survival statistical analysis. No failures were observed at Yz monolithic 1.5 mm. High and similar performance was observed for Cad-On groups and Yz monolithic 1.0 mm. The control group depicted the worst behavior. The Weibull modulus of CAD-on 1.5 mm was higher than the control while being similar to the other conditions. Both the monolithic systems and the CAD-on technique showed high and similar fatigue fracture behavior and survival rates, which were also higher than the control bilayer system. Both systems reduced the occurrence of delamination failures, making them suitable for clinical use.

Resumo Este estudo teve como objetivo avaliar o comportamento à fadiga de estruturas cerâmicas monolíticas de zircônia (Yz) e multicamadas utilizando a técnica CAD-on em diferentes espessuras. Cinquenta (N=50) preparos unitários padronizados foram confeccionados em resina epóxi reforçada com fibra de vidro (NEMA grau G10), digitalizados e as restaurações usinadas em CAD-CAM, compondo 5 grupos (n= 10): Controle: 1,5 mm (estrutura de zircônia fresada + porcelana estratificada manualmente); Yz monolítica 1,5 mm; Yz monolítica 1,0 mm; CAD-on em 1,5 mm; e CAD-on 1,0 mm (estrutura de zircônia fresada com 0,5 mm de espessura ligada por uma cerâmica de baixa fusão a uma camada de dissilicato de lítio fresado de 1,0 mm ou 0,5 mm, respectivamente). As bases do G10 foram condicionadas com ácido fluorídrico a 10%; as coroas foram jateadas com partículas de alumina de 110 μm; e então cimentadas uma sobre a outra com cimento resinoso autoadesivo. Foi realizado um teste de fadiga cíclica (carga inicial: 400N para 10.000 ciclos, frequência de 20 Hz, step de 200N) até a falha, e os dados foram submetidos a uma análise estatística de sobrevivência. Nenhuma falha foi observada para Yz monolítica de 1,5 mm. Desempenho alto e semelhante foi observado para os grupos Cad-On e Yz monolítica 1,0 mm. O grupo controle apresentou o pior comportamento. O módulo de Weibull do CAD-on 1,5 mm foi maior que o grupo controle, sendo semelhante às outras condições. Tanto os sistemas monolíticos quanto a técnica CAD-on apresentaram alto e semelhante desempenho mecânico e taxas de sobrevivência, que também foram superiores ao sistema bicamada de controle. Ambos os sistemas reduziram a ocorrência de falhas de delaminação, tornando-os adequados para uso clínico.

Fatigue performance of adhesively luted glass or polycrystalline CAD-CAM monolithic crowns.

STATEMENT OF PROBLEM: Data comparing the fatigue performance of adhesively luted glass or polycrystalline ceramic systems for computer-aided design and computer-aided manufacturing (CAD-CAM) are scarce. PURPOSE: The purpose of this in vitro study was to evaluate and compare the fatigue performance of monolithic crowns manufactured from glass or polycrystalline CAD-CAM ceramic systems adhesively luted to a dentin analog. MATERIALS AND METHODS: Fifty-four pairs of standardized preparations of dentin analog (NEMA Grade G10) and simplified ceramic crowns of 1.5-mm thickness were obtained with 3 ceramic materials: lithium disilicate (LD) glass-ceramic (IPS e.max CAD); zirconia-reinforced lithium silicate (ZLS) glass-ceramic (Vita Suprinity); and translucent yttrium fully stabilized polycrystalline zirconia (Trans YZ) (Prettau Anterior). The simplified crowns (n=15) were adhesively cemented onto the preparations and subjected to step-stress fatigue test (initial load of 400 N, 20 Hz, 10 000 cycles, followed by 100-N increment steps until failure). Collected data (fatigue failure load [FFL] and cycles for failure [CFF]) were submitted to survival analysis with the Kaplan-Meier and Mantel-Cox post hoc tests (α=.05) and to Weibull analysis (Weibull modulus and its respective 95% confidence interval). Failed crowns were submitted to fractography analysis. The surface characteristics of the internal surface (roughness, fractal dimension) of additional crowns were accessed, and the occlusal cement thickness obtained in each luted system was measured. RESULTS: Trans YZ crowns presented the highest values of FFL, CFF, and survival rates, followed by ZLS and LD (mean FFL: 1740 N>1187 N>987 N; mean CFF: 149 000>92 613>73 667). Weibull modulus and cement thickness were similar for all tested materials. LD presented the roughest internal surface, followed by ZLS (mean Ra: 226 nm>169 nm>93 nm). The LD and ZLS internal surfaces also showed higher fractal dimension, pointing to a more complex surface topography (mean fractal dimension: 2.242=2.238>2.147). CONCLUSIONS: CAD-CAM monolithic crowns of Trans YZ show the best fatigue performance. In addition, ZLS crowns also showed better performance than LD crowns.

Assessment of stress/strain in dental implants and abutments of alternative materials compared to conventional titanium alloy-3D non-linear finite element analysis.

The aim of this study was to assess the stress/strain in dental implant/abutments with alternative materials, in implants with different microgeometry, through finite element analysis (FEA). Three-dimensional models were created to simulate the clinical situation of replacement of a maxillary central incisor with implants, in a type III bone, with a provisional single crown, loaded with 100 N in a perpendicular direction. The FEA parameters studied were: implant materials-titanium, porous titanium, titanium-zirconia, zirconia, reinforced fiberglass composite (RFC), and polyetheretherketone (PEEK); and abutment materials-titanium, zirconia, RFC, and PEEK; implant macrogeometry-tapered of trapezoidal threads (TTT) and cylindrical of triangular threads (CTT) (ø4.3 mm × 11 mm). Microstrain, von Mises, shear, and maximum and minimum principal stresses in the structures and in peri-implant bone were compared. There was increased stress and strain in peri-implant bone tissue caused by implants of materials with lower elastic modulus (mainly for PEEK and RFC). They also presented higher concentration of stresses in the implant itself (especially RFC). Zirconia implants led to lower stress and strains in peri-implant bone tissue. Less rigid abutments (RFC and PEEK) associated with titanium implants led to higher stress in the implant and in peri-implant bone tissue. The TTT macrogeometry showed a higher stress concentration in the implant and peri-implant bone tissue. The stress/strain in peri-implant bone tissue and implant structures were affected by the material used, where reduced values were caused by stiffer materials. Lower stress/strain values were obtained with cylindrical implants of triangular treads.

Microstructure, topography, surface roughness, fractal dimension, internal and marginal adaptation of pressed and milled lithium-disilicate monolithic restorations.

PURPOSE: To characterize the effect of two processing techniques (pressing and CAD/CAM - Computer Aided Design/Computer Aided Machining) of lithium-disilicate (LD) based crowns on the microstructure, topography, roughness, fractal dimension, internal and marginal adaptation. METHODS: One-hundred identical preparations for monolithic crowns were made with dentin analogue material (G10 epoxy resin). One of the preparations was scanned and a monolithic crown in lithium-disilicate was planned in the CAD system. Fifty crowns were milled in a wax pattern and subjected to pressing (IPS e.max Press), while 50 crowns were machined at CAD/CAM (IPS e.max CAD) and posteriorly crystallized. Internal and marginal adaptation were assessed via replica technique at four manufacturing moments (Milled wax pattern; LDPRESS; Milled LDCAD; Crystallized LDCAD) and considering 5 regions (margin, cervico-axial angle, axial wall, axial-occlusal angle and occlusal wall). Complementary analysis considering microstructure and topography, roughness and fractal dimension were performed in Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). RESULTS: The processing technique resulted in different ceramic microstructure, topography, roughness and fractal dimension, whereas CAD/CAM lead to smoother, more homogeneous but more complex topography features (higher fractal dimension) in comparison to the pressing technique (P<0.05). Regarding marginal and internal fit, LDPRESS crowns showed to be more adapted at the margin, while LDCAD were more adapted at the occluso-axial angle; other regions were not statistically different (α=0.05). CONCLUSIONS: CAD/CAM and the pressing techniques for manufacturing LD crowns lead to completely different ceramic surface characteristics and affect crown adaptation at the margin and at occluso-axial angle.

Influence of inorganic filler content of resin luting agents and use of adhesive on the performance of bonded ceramic.

STATEMENT OF PROBLEM: The inorganic filler of resin-based luting agents and the use of an adhesive layer could influence the bonding ability, mechanical performance, and interface morphology of bonded feldspathic ceramic. PURPOSE: The purpose of this in vitro study was to investigate the influence of resin-based luting agents loaded with different inorganic filler content, with or without an adhesive, on microtensile bond strength, biaxial flexural strength, and the adhesive interface morphology of bonded ceramic specimens. MATERIAL AND METHODS: Experimental resin-based luting agents with low (55wt%), intermediate (65wt%), and high (75wt%) filler contents were bonded to ceramic specimens, with or without a layer of adhesive. The resin-based luting agents were characterized by measuring viscosity, elastic modulus, Poisson ratio, and degree of conversion (n=3 for each test). The response variables for the bonded ceramic specimens were ceramic-resin microtensile bond strength (n=30), biaxial flexural strength (n=30) and characteristic strength, and Weibull modulus. Scanning electron microscopy was used for fractographic and interface analyses of the specimens fractured in the microtensile test (n=3). Data were subjected to ANOVA with the post hoc Tukey test (α=.05). Weibull moduli were also calculated. RESULTS: Increased inorganic filler content yielded significantly higher viscosity, stiffness, and film thickness. However, the Poisson ratio and degree of conversion were not affected. The lowest bond strength values were observed for the resin-based luting agents with high inorganic filler content when no adhesive was used and for the resin-based luting agent with low filler content when the adhesive was used. The increase in filler content of the resin-based luting agent appeared to be associated with a higher frequency of mixed failures. Increased filler content resulted in higher biaxial flexural and characteristic strength and decreased structural reliability. The adhesive helped fill irregularities on ceramic and slightly increased film thickness but had only a minor effect on mechanical strength. CONCLUSIONS: Experimental resin-based luting agent loaded with high inorganic filler content strengthened the bonded feldspathic ceramic and yielded significantly higher viscosity and film thickness. In contrast, the bond strength was lower if no adhesive was used.

Restorative Possibilities Using Zirconia Ceramics for Single Crowns.

Two clinical cases are presented to explore technical differences and discusses the advantages and disadvantages of using veneered or monolithic zirconia to manufacture posterior single crowns. The first case describes the clinical steps in manufacturing a monolithic crown on a mandibular left second premolar using high translucency zirconia. It shows the use of a conservative tooth preparation based on the superior mechanical properties that this material presents as well as the final optical characteristics achieved by shading and staining. In the second case, a conventional bilayer restorative treatment was made using zirconia framework followed by veneering with feldspar ceramic on a mandibular left first molar. Recent literature indicates that each of these restorative alternatives presents specific advantages and disadvantages. Factors such as mechanical performance, fracture, esthetic characteristics, clinical success, complication rates, adhesion and antagonist wear performance are discussed comparing the two restorative assemblies. The data highlight that monolithic crowns prevent a major problem reported on bilayer restorations: the chipping of veneering ceramic. Monolithic crowns also allow minimally invasive tooth preparations, thus increasing tooth remnant preservation. However, data that support esthetic performance similarity between monolithic and bilayer assemblies are lacking, thus the predictability of use is restricted for the posterior region, as cases demanding high esthetic appeal continue to fundamentally use bilayer restorations. Failures were not found, and patient satisfaction was reported in both techniques after the 12-month follow up.

Do endodontic retreatment techniques influence the fracture strength of endodontically treated teeth? A systematic review and meta-analysis.

One of the major concerns about endodontically retreated teeth (ERT) is undoubtedly its loss of remnant structure, which could lead to consequently greater fracture risk. Therefore, the objective of this systematic review is to assess the influence of endodontic retreatment on the fracture strength of the dental tooth remnant. In vitro studies assessing the influence of mechanical retreatment on the mechanical properties (static or under fatigue) of restored teeth were searched in PubMed and SCOPUS databases. Three independent reviewers screened titles/abstracts of articles and the full-text of potentially eligible studies. The risk of bias was independently assessed by one researcher and verified by another two. Comparison between the mean load to fracture of teeth after endodontic treatment and after endodontic retreatment were estimated using pairwise random effects meta-analysis to calculate pooled mean differences. Three studies were included for the systematic review and 2 for the meta-analysis. The pooled effect indicated a statistical difference (Mean difference: -121.03 95%CI: -183.02, -59.05) between conditions favoring the endodontically treated teeth. However, the low number of studies combined with their heterogeneity made it difficult to prove such phenomenon. ERT might present lower fracture strength than endodontically treated teeth. However, more coherent laboratory tests may provide better evidence and quantitative parameters on how much reliability can be attributed to an endodontic retreatment, in addition to which technique can provide more predictable results in this conservative approach.

Different fabrication techniques of implant-supported prostheses: microhardness and fracture strength

Aim: This study evaluated the mechanical behavior of implant-supported crowns obtained by different fabrication technique after thermomechanical cycling. Methods: Thirty-two external hexagon dental implants were divided into four groups (n=10): CC ­ conventional casting with torch; EI ­ electromagnetic induction casting; PL ­ plasma casting; and CAD-CAM ­ milling through computer-aided design and computer-aided manufacturing. Vickers microhardness of the specimens were made before and after the thermomechanical cycling, and then subjected to fracture load. Fracture pattern was evaluated. Results: No significant difference was observed comparing the microhardness before and after thermomechanical cycling. CAD-CAM group presented significant lower microhardness than the other groups. No significant statistical difference was showed on fracture load between the groups. The CAD-CAM and PL presented lower number of failure by plastic deformation. Conclusion: The manufacturing techniques affected the mechanical behavior and the failure pattern of implant-supported crowns tested

Inorganic filler content of resin-based luting agents and the color of ceramic veneers.

The influence of inorganic filler content of resin-based luting agents (RBLAs) on color change (ΔE00), CIEL*a*b* (individual color coordinates), and translucency parameters (TP) of simulated ceramic laminate veneer (CLV) was investigated. RBLAs with low, intermediate, and high inorganic filler content (55%, 65%, and 75% mass fractions, respectively) were prepared. Feldspar ceramic (Vitablocs Mark II) specimens (1.2 mm × 0.8 mm, A1C shade) were bonded to simulated composite resin substrates (1.6 mm × 1.2 mm, A2D shade) using three experimental and a commercial (RelyX Veneer) RBLA (translucent shade). The ΔE00 was calculated by CIEDE2000 color difference metric under three conditions (before, immediately after, and 24 h after luting). The TP was calculated using CIEL*a*b* color coordinates measured over white and black backgrounds. Surface morphology of the RBLAs was analyzed. One-way and two-way analyses of variance with a post-hoc Tukey's test were used respectively to calculate TP, CIEL*a*b* coordinates, and ΔE00 (α= 0.05). Overall, the tested RBLAs presented clinically visible ∆E00 values under the three conditions evaluated. For all RBLAs, higher ∆E00 values were observed between measurements obtained before and immediately after luting. Different inorganic filler content did not significantly increase the opacity of the ceramic-luting agents-resin composite set. The variation in inorganic filler content did not influence significantly the TP of simulated CLV; although all of the experimental RBLAs tested yielded ∆E00 above the perceptibility threshold. The L*, a*, and b* individual color coordinates were cementation-dependent.

Feldspar Ceramic Strength and The Reinforcing Effect by Adhesive Cementation Under Accelerated Aging.

This study evaluated the effect of the accelerated artificial aging (AAA) on feldspar ceramic strength and the reinforcing effect promoted by adhesive cementation with resin luting agent. One hundred twenty feldspar ceramic disks were obtained. Sixty disks were acid-etched, silanized, and coated with an experimental resin luting agent simulating the adhesive luting procedures. Four groups were created (n=30): uncoated ceramic (control group), uncoated ceramic submitted to AAA, ceramic coated with resin luting agent, and coated ceramic submitted to AAA. Biaxial flexural testing with ball-on-ring setup was carried out. Biaxial flexural strength (s bf , MPa), characteristic strength (s 0 , MPa), and Weibull modulus (m) were calculated for axial positions z=0 (ceramic surface) and z=-t2 (luting agent surface). Data of s bf at positions z=0 and z=-t2 were separately submitted to statistical analyses (a=0.05). The uncoated ceramic submitted to AAA had no significant difference in s bf and s 0 compared with the control group. Resin coating of the ceramic increased s bf and s 0 at z=0. The AAA increased the s bf and s 0 for the resin-coated ceramic specimens at z=0 and also the s 0 at axial position z=-t2. The structural reliability at z=0 and z=-t2 was not influenced by the variables tested. In conclusion, resin coating improved the mechanical strength of the feldspar ceramic. The AAA procedure was not effective in aging the uncoated or resin-coated feldspar ceramic specimens.

Parafunctional loading and occlusal device on stress distribution around implants: A 3D finite element analysis.

STATEMENT OF PROBLEM: An occlusal device is frequently recommended for patients with bruxism to protect implant-supported restorations and prevent marginal bone loss. Scientific evidence to support this treatment is lacking. PURPOSE: The purpose of this 3-dimensional (3D) finite element study was to evaluate the influence of an acrylic resin occlusal device, implant length, and insertion depth on stress distribution with functional and parafunctional loadings. MATERIAL AND METHODS: Computer-aided design software was used to construct 8 models. The models were composed of a mandibular bone section including the second premolar and first and second molars. Insertion depths (bone level and 2 mm subcrestal) were simulated at the first molar. Three natural antagonist maxillary teeth and the placement or not of an occlusal device were simulated. Functional (200-N axial and 10-N oblique) and parafunctional (1000-N axial and 25-N oblique) forces were applied. Finite element analysis (FEA) was used to determine the maximum principal stress for the cortical and trabecular bone and von Mises for implant and prosthetic abutment. RESULTS: Stress concentration was observed at the abutment-implant and the implant-bone interfaces. Occlusal device placement changed the pattern of stress distribution and reduced stress levels from parafunctional loading in all structures, except in the trabecular bone. Implants with subcrestal insertion depths had reduced stress at the implant-abutment interface and cortical bone around the implant abutment, while the stress increased in the bone in contact with the implant. CONCLUSIONS: Parafunctional loading increased the stress levels in all structures when compared with functional loading. An occlusal device resulted in the lowest stress levels at the abutment and implant and the most favorable stress distribution between the cortical and trabecular bone. Under parafunctional loading, an occlusal device was more effective in reducing stress distribution for longer implants inserted at bone level. Subcrestally, implant insertion yielded the most favorable biomechanical conditions at the abutment-implant interface and at the coronal surface of the cortical bone, mainly when there was no occlusal device.

Resin cements formulated with thio-urethanes can strengthen porcelain and increase bond strength to ceramics.

OBJECTIVES: The use of thio-urethane oligomers has been shown to significantly improve the mechanical properties of resin cements (RCs). The aim of this study was to use thio-urethane-modified RC to potentially reinforce the porcelain-RC structure and to improve the bond strength to zirconia and lithium disilicate. METHODS: Six oligomers were synthesized by combining thiols - pentaerythritol tetra-3-mercaptopropionate (PETMP, P) or trimethylol-tris-3-mercaptopropionate (TMP, T) - with di-functional isocyanates - 1,6-Hexanediol-diissocyante (HDDI) (aliphatic, AL) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (BDI) (aromatic, AR) or Dicyclohexylmethane 4,4'-Diisocyanate (HMDI) (cyclic, CC). Thio-urethanes (20 wt%) were added to a BisGMA/UDMA/TEGDMA organic matrix. Filler was introduced at 60 wt%. The microshear bond strength (µSBS), Weibull modulus (m), and failure pattern of RCs bonded to zirconia (ZR) and lithium disilicate (LD) ceramics was evaluated. Biaxial flexural test and fractographic analysis of porcelain discs bonded to RCs were also performed. The biaxial flexural strength (σbf) and m were calculated in the tensile surfaces of porcelain and RC structures (Z = 0 and Z = -t2, respectively). RESULTS: The µSBS was improved with RCs formulated with oligomers P_AL or T_AL bonded to LD and P_AL, P_AR or T_CC bonded to zirconia in comparison to controls. Mixed failures predominated in all groups. σbf had superior values at Z = 0 with RCs formulated with oligomers P_AL, P_AR, T_AL, or T_CC in comparison to control; σbf increased with all RCs composed by thio-urethanes at Z = -t2. Fractographic analysis revealed all fracture origins at Z = 0. CONCLUSION: The use of specific thio-urethane oligomers as components of RCs increased both the biaxial flexural strength of the porcelain-RC structure and the µSBS to LD and ZR. CLINICAL SIGNIFICANCE: The current investigation suggests that it is possible to reinforce the porcelain-RC pair and obtain higher bond strength to LD and ZR with RCs formulated with selected types of thio-urethane oligomers.

Mechanical properties and superficial characterization of a milled CAD-CAM glass fiber post.

Computer-aided design and computer-aided manufacturing (CAD-CAM) technology may be used to produce custom intraradicular posts, but studies are lacking. The purpose of this in vitro study was to evaluate the flexural properties (strength and modulus), failure mode, superficial morphology, and roughness of two CAD-CAM glass fiber posts (milled at different angulations) compared with a commercially available prefabricated glass fiber post. Three groups were tested (n = 10): PF (control group)- prefabricated glass fiber post; C-Cd-diagonally milled post; and C-Cv-vertically milled post. A 3-dimensional virtual image was obtained from a prefabricated post, which guided the posterior milling of posts from a glass fiber disk (Trilor Blanks; Bioloren). Surface roughness and morphology were evaluated using confocal laser microscopy. Flexural strength and modulus were evaluated with the 3-point bend test. Data were submitted to one-way analysis of variance followed by the Student-Newman-Keuls post hoc test (α = 0.05). The fractured surfaces were evaluated with scanning electron microscopy. The superficial roughness was highest for PF and similar for the experimental groups. Morphological analysis shows different sizes and directions of the glass fibers along the post. The flexural strength was highest for PF (900.1 ±â€¯30.4 > C-Cd - 357.2 ±â€¯30.7 > C-Cv 101.8 ±â€¯4.3 MPa) as was the flexural modulus (PF 19.3 ±â€¯2.0 GPa > C-Cv 10.1 ±â€¯1.9 GPa > C-Cd 7.8 ±â€¯1.3 GPa). A CAD-CAM milled post seems a promising development, but processing requires optimizing, as the prefabricated post still shows better mechanical properties and superficial characteristics.

Inorganic filler content of resin-based luting agents and the color of ceramic veneers

Abstract The influence of inorganic filler content of resin-based luting agents (RBLAs) on color change (ΔE00), CIEL*a*b* (individual color coordinates), and translucency parameters (TP) of simulated ceramic laminate veneer (CLV) was investigated. RBLAs with low, intermediate, and high inorganic filler content (55%, 65%, and 75% mass fractions, respectively) were prepared. Feldspar ceramic (Vitablocs Mark II) specimens (1.2 mm × 0.8 mm, A1C shade) were bonded to simulated composite resin substrates (1.6 mm × 1.2 mm, A2D shade) using three experimental and a commercial (RelyX Veneer) RBLA (translucent shade). The ΔE00 was calculated by CIEDE2000 color difference metric under three conditions (before, immediately after, and 24 h after luting). The TP was calculated using CIEL*a*b* color coordinates measured over white and black backgrounds. Surface morphology of the RBLAs was analyzed. One-way and two-way analyses of variance with a post-hoc Tukey's test were used respectively to calculate TP, CIEL*a*b* coordinates, and ΔE00 (α= 0.05). Overall, the tested RBLAs presented clinically visible ∆E00 values under the three conditions evaluated. For all RBLAs, higher ∆E00 values were observed between measurements obtained before and immediately after luting. Different inorganic filler content did not significantly increase the opacity of the ceramic-luting agents-resin composite set. The variation in inorganic filler content did not influence significantly the TP of simulated CLV; although all of the experimental RBLAs tested yielded ∆E00 above the perceptibility threshold. The L*, a*, and b* individual color coordinates were cementation-dependent.

Biomechanical behavior of teeth without remaining coronal structure restored with different post designs and materials.

The aim of this study was to access the biomechanical behavior of teeth without remaining coronal structure when restored with posts of different materials and configurations. Fifty bovine teeth (n=10 per group) with standard dimensions were restored as follows: cast post and core (CPC), prefabricated metallic post (PFM), parallel glass-fiber post (P-FP), conical glass-fiber post (C-FP) or composite core (no post, CC). The survival rate during thermomechanical challenging (TC), the fracture strength (FS), and failure pattern (FP) were evaluated. Finite element models were realized to evaluate the stress distribution with a 100N load. All post-containing teeth survived TC, while CC had 30% of failures. CPC and C-FP had the higher fracture strength, but a high number of irreparable fractures (60%), such as PFM (70%). Von Mises analysis has shown the maximum stresses into the canal in groups restored with metallic posts, while glass-fiber posts and CC presented the maximum stresses at load contact point in the crown. CPC led to higher modified von Mises (mvM) stress in the cervical third of dentin. However, mvM values did not reach the dentin fracture limit for any group. Analysis of maximal contact pressure has shown better stress distribution along with the dentin interface in post-containing groups, especially for CPC.

Reabilitação oral ­ parte 1: prótese total implantossuportada na mandíbula associada a próteses cerâmicas na maxila / Oral rehabilitation ­ part 1: mandibular implant-supported denture associated to maxillary ceramic dental prostheses

A presente coluna teve como objetivo apresentar um relato de caso clínico de reabilitação oral envolvendo diferentes possibilidades em prótese dentária: uma prótese total fixa implantossuportada (PTF) na mandíbula; e restaurações cerâmicas com infraestruturas de dissilicato de lítio sobre os dentes remanescentes e infraestruturas de zircônia sobre os implantes. O tratamento foi desenvolvido em quatro etapas: i) restabelecimento da dimensão vertical de oclusão (DVO); ii) PTF na mandíbula; iii) reabilitação temporária superior; e iv) próteses cerâmicas superiores. A coluna foi dividida em duas partes: 1) etapas i, ii e iii; e 2) etapa iv. Após o acompanhamento clínico de quatro anos da PTF na mandíbula e seis meses das próteses cerâmicas superiores, a reabilitação apresentou-se satisfatória do ponto de vista estético e funcional.

The purpose of this column was to present a clinical case report of oral rehabilitation involving different possibilities in dental prosthesis: a fixed implant-supported denture (FD) on the jaw; and ceramic restorations with lithium disilicate frameworks on the remaining teeth and zirconia frameworks on the implants. The treatment was developed in four steps: i) reestablishment of the vertical occlusion dimension (OVD); ii) FD on the jaw; (iii) maxil-lary temporary rehabilitation; and iv) ceramic prostheses on the maxillary. The column was divided into two parts: 1) steps i, ii and iii; and 2) step iv. After the four-year of FD clinical follow-up and six months of the superior ceramic prostheses, the rehabilitation was considered aesthetic and functional satisfactory.

Ensuring passivity and retrievability for immediate complete-arch implant-supported prostheses.

This technique describes the fabrication of frameworks for immediate complete-arch implant-supported prostheses to ensure that the dimensional alterations that occur during the casting procedure do not interfere with passivity. As sectioning and soldering are not necessary, there is no delay in the fabrication process, and the framework is not weakened. Titanium abutments for interim screw-retained prostheses are prepared on the definitive cast, and framework waxing preserves the access holes to the screws. After casting, the framework is cemented on the prepared abutments. The proposed technique has been created to combine the advantages of cement-retained frameworks and the retrievability of screw-retained ones.

Use of Feldspathic Porcelain Veneers to Improve Smile Harmony: A 3-Year Follow-up Report.

This case report describes an esthetic treatment to improve the shape and alignment of the anterior teeth, reestablishing smile harmony, using feldspathic porcelain veneers. Results of clinical follow up after 36 months are also presented. The advantages, disadvantages and limitations of the technique are detailed with reference to the relevant literature. This suggests that the success of treatment depends on adequate conditions of bonding between the veneers and the tooth complex, which involves parameters such as the strength and durability of the bond interface. Therefore, the clinical success of feldspathic porcelain veneers depends on the accurate selection of cases and correct execution of clinical and laboratory procedures. The rehabilitation involved from first right premolar to the left with feldspathic porcelain veneers made on refractory dies. After the 3-year follow up, excellent clinical results and patient satisfaction were achieved.